Your warehouse, shop, or facility floor needs a coating system designed for the load it carries - not a residential product stretched to fit. We build heavy-duty epoxy systems for Plantation and Broward County commercial spaces, with moisture testing and proper prep every time.

Commercial and industrial epoxy floor coatings in Plantation, FL use a multi-layer system - primer, one or more base coats, and a protective topcoat - applied to a concrete slab that has been mechanically profiled and tested for moisture. Most projects take two to five days from start to return-to-use, depending on the square footage and how much prep work the slab requires.
A residential garage coating and a commercial warehouse floor are fundamentally different jobs. Commercial floors face forklift traffic, chemical spills, heavy point loads from racking systems, and constant foot traffic. They need a thicker system with the right topcoat for the specific use - a showroom gets a different finish than a food-service kitchen or a distribution center. Getting that match wrong means a floor that looks fine on day one but starts chipping and peeling under real working conditions within months.
If you are looking at options for a garage or residential space instead, our epoxy floor coatings page covers residential systems and what to expect for a home project.
If you run your hand across the floor and it comes away with fine gray powder, the concrete surface is breaking down. In Plantation's humid climate, this process can accelerate once it starts - sweeping and mopping will not fix it. A fresh epoxy coating seals the surface and stops the dusting for good.
Oil stains, chemical spills, and rust marks that have soaked into bare concrete are nearly impossible to remove completely. If your floor looks permanently dirty no matter how often it gets mopped, the concrete has absorbed years of contamination. Epoxy over properly prepared concrete gives you a non-porous surface that wipes clean and prevents new stains from soaking in.
Small surface cracks and chips are normal in older concrete, but they grow if left alone - especially in South Florida, where the ground shifts slightly during the wet season as soil absorbs and releases water. If cracks have widened or new ones have appeared, a coating now is far less expensive than structural repairs later.
If you already have an epoxy or paint coating on the floor and it is lifting at the edges, bubbling in patches, or worn down to bare concrete in high-traffic areas, the coating has reached the end of its life. Peeling in Plantation is often a sign the original coating went over a damp slab - a common problem in this climate that a recoat needs to address at the root.
We install commercial and industrial epoxy coating systems throughout Plantation and the surrounding Broward County corridor - including the warehouse and light industrial facilities clustered along I-595 and the Sawgrass Expressway. Every job starts with a full slab assessment, moisture testing, and mechanical surface preparation. We do not skip prep to move faster. That is the step that determines whether your floor lasts five years or five months.
Our commercial systems cover everything from solid-color warehouse floors to high-build chemical-resistant systems for facilities where spills are a daily reality. If your space has heavy equipment, forklift traffic, or specific chemical exposure, we build the coating system around those requirements - not around what is fastest for us to install. We also handle full removal and recoating for floors where an older system has failed. For facilities that need a flooring option with higher thermal and chemical resistance than epoxy, our urethane cement flooring is worth considering alongside the standard epoxy options. Businesses that also need separate garage bays handled can ask about our garage floor coatings.
High-build multi-coat epoxy with a urethane or polyaspartic topcoat - designed for forklift traffic, heavy racking loads, and daily cleaning.
Decorative metallic or solid-color systems with a high-gloss topcoat - built to look sharp under commercial lighting and handle foot traffic.
Thicker, high-build coatings formulated to resist specific chemicals - appropriate for manufacturing, automotive service, and light processing facilities.
Full removal of existing failing coatings, moisture remediation if needed, and a fresh system applied to bare, prepared concrete.
Plantation and the Broward County corridor along I-595 host a dense cluster of warehouses, distribution centers, light manufacturing facilities, and commercial flex spaces. Almost every one of them sits on a concrete slab poured at ground level - which means the floor is in direct contact with the soil and groundwater below. This creates a constant upward moisture pressure that a contractor has to account for before any coating goes down. Skipping moisture testing on a slab-on-grade floor in South Florida is how businesses end up paying to recoat a floor that was only installed two years ago.
The Occupational Safety and Health Administration also notes that smooth, worn, or contaminated floors are a leading cause of workplace slip-and-fall incidents - a real risk in any busy facility. A properly finished epoxy floor with anti-slip texture addresses that. We serve businesses throughout the area, including facilities in Fort Lauderdale and Miramar, with the same prep standards and moisture testing on every project.
We ask a few basic questions - the size of the space, what the floor is currently used for, and whether there is an existing coating. We respond within one business day and schedule a free on-site visit. You do not need the exact square footage - a rough idea gets us started.
We visit the facility, check for cracks, stains, moisture, and the condition of any existing coating. We test the slab for moisture - a non-negotiable step in South Florida. You get a written, itemized quote covering prep, materials, and number of coats before any work begins.
Everything needs to be off the floor before the crew arrives - equipment, shelving, vehicles, and stored items. The crew then grinds the surface, fills cracks, and applies a moisture-blocking primer if the slab tests high. This prep work is what determines whether the floor lasts.
We apply the system in layers over one to four days depending on scope. Light foot traffic is typically safe after 24 hours; heavy equipment needs 72 hours minimum. We walk the floor with you before we leave and explain how to clean and maintain the surface going forward.
We walk the floor with you, test for moisture, and give you a clear, itemized number before any work begins. No pressure, no surprises.
(754) 318-0003We have coated floors in Plantation-area warehouses, distribution centers, and commercial facilities that see heavy daily use. We build the coating system to match what your specific floor will face - not a one-size residential product applied to an industrial slab.
We hold a valid Florida state contractor's license and carry full liability coverage. You can verify our license through the Florida Department of Business and Professional Regulation before signing anything. A licensed contractor is accountable to the state if something goes wrong.
Shutting down a commercial space costs money. We plan every project around your schedule and are experienced working over weekends and during planned shutdowns so your operation is back up as fast as possible - with a clear timeline given to you before we start.
Plantation's slab-on-grade construction and high water table make moisture testing non-negotiable. We test every floor before we touch it and use a primer designed for humid Florida conditions. That is why our floors do not bubble and peel the way rushed jobs do.
We have been working on commercial and industrial floors in this area since 2018. That means we know the local building stock, the soil conditions, and the seasonal patterns that affect how epoxy performs in South Florida. Call us and get a contractor who already understands what your floor is up against.
Residential garage systems with decorative flake or solid-color finishes, anti-slip texture included.
Learn MoreA thermal-shock-resistant flooring system for commercial kitchens, food processing, and cold-storage facilities.
Learn MoreFall and winter fill up fast with commercial projects - reach out now and we will have a written quote to you within one business day.